Видео

Ask Joe anything, but he won't answer.

The Pro Neck is new to. I have been using M dies for pistol calibers, is that the wrong choice?

Lyman, you guys make some really and truly great products. i've got so many and when i need/want an accessory, upgrade or the "shaddup and take mah munneh!!!" item, i look to your site first. but with this redesign of the grip...i hate to say it kinda falls short. the grip's beaver tail needs to be thinned down to around 1/8" to 1/4" thickness to afford the user a higher purchase of engagement. the grip's angle needs to be somewhere around 12.5 degrees. i figure 13 on the high side and 12 on the low just due to the way the human wrist articulates when using the AR platform whether the user is wearing a t-shirt, jacket/windbreaker or winter coat or body armor. the grippy-grip texture is just fine and so are the finger "nubs". thank you for reviewing my comment and i meant it that before i go to brownells, midwayUSA or anywhere else i go to you site first. p.s. Pachmayr needs to bring back the Dominator...y'all know what i mean. 10", 12" and 14" barrels

What sidesaddle attachment are you using?

Lyman's is the first reloading manual a new reloader should get.

Too bad the .223 lyman trim die keeps sticking the case in the die. I used clean lubed once fired brass after it was full length sized.

I thought it was a really bad idea to use plastic pellets in a vibratory tumbler?

Great video, Thank you! The instructions that came with it are crap. Even the video doesn't tell us that the thicker washers are the spacers, but I figured it out. I've had one of these traps back in the 90s and they're GREAT!

Do yourself a favor and by a lortone barrel tumbler. None of the stones depicted in this ad were used to make the jewelry they place next to tumbled stones. Vibratory tumblers work best dry tumbling metal.

I hear the steel pins will wear the aluminum receiver under heavy loads on the maverick 88 ... any truth to that ? 🤔

Feed the snake lol, honestly made me laugh until tearing up haha.

Does this grip ever slide up and activate the grip safety?? please respond? thank you

✌️👍‼️

I have 870 express Magnum is there a difference between the 870 express and magnum?

I feel, wet tumbling it's the way of the future.

can you use dummy rounds at home? does it hurt people?

I just put my brass in a container with hot water a spoonful of dish soap and a spoonful, of Lemon juice, shake it for a minute then done. Works and looks great been working for years Brass only lasts so many firings anyway….

Can you tell me what pilot number when using universal trimmer for 300 blk caliber ? Thank you

Great new product. Pretty intuitive. Thanks - SOTAR alumni and this’ll come in handy.

❤️‍🩹🇺🇸🙏🇺🇸❤️‍🩹

Price: 2016: $1,595 2024: $2,600 I wonder if they gave their employees 63% raises over that period of time.

Mine doesn't trim the .308 down for enough

Does anyone know a way to stop this tumbler from blowing dry polish out of the bowl? I'm polishing with corn cob media and very expensive dry polish. After a couple of hours I have dry polish dust all around the tumbler bowl and base. I have it on very tight too. I worry if I was doing a wet polish there could be water getting out as well. Anyone know of a rubber seal or anything that could help keep everything in the tumbler?

Terrible written directions! Great video! Could not have ever put it together without this video, thanks 🙏 😊

Why do they fall short of the top of the grip frame by so much, the #02478 Diamond Pro grip on the S&W 442/642? And many other J-frame Smiths. I see so many install videos with about an inch or so of exposed backstrap and clearly a person would not be able to achieve a high grip on the revolver. That's why my Pachmayrs have never been installed onto my 642, but I did install Hogue Tamer #60020 grips and they are excellent. I really want to use the Pachmayr Diamond Pro grips, but the design fit is seriously lacking in my opinion.

what if the barrel wedges fall out?

I hope so but would it be great if the diamond pro grips were made of polymer instead of the useless rubber grip that other companies keep making? Seriously they don't work at all!

I have ordered this stand. Looks like a really solid unit.

That’s a great one

Cleaning brass is a waste of time. Unless there is physical hard dirt on it, just reload like that. All this equipment is just to get into your wallet.

Will I need to crimp after using the M Die for .300blk ?

I’ve called Lyman for warrenty replacement. Even the one they sent me didn’t work. Does not seat the primer deep enough !

Very disappointing; I'm considering returning mine. You have to hold it at exactly the right angle or the primers fall out of the case and the ram will not press the primer into the hole. Also, it does not seat the primers deep enough unless you apply considerable force/grip strength. The tray also does not encourage the primers to align themselves right way up. It provides better tactile feedback than my Hornday on-press primim system, but still, very disappointing.

Great video, thanks for sharing.

looking for a speed loader for a 38 colt diamondback

I dig that work bench in the background. Where did you get it?

You can get media lodging with steel pins

Just wanted to drop in and tell you guys and girls over at Lyman. I was gifted a brass smith All American 8 and I’m in love. 12/25/23 merry Christmas Lyman

I got mine together but can’t figure out for it to shoot straight out and longer. Help

That ultrasonic machine looks like the one from Harbor freight. I use $70 Vevor 3L ultrasonic cleaner, water/dawn/dishwasher magic, and a free dehydrator from craigslist. Results are great (and cheap!). Plus I can clean large parts (carburetors, etc) and make jerky.

Maybe repost this WITHOUT the music!

I have pre-ordered this back in January, and I am still waiting!😞😞😞

I have that same forend and shell holder blocks the forend halfway back. Can't rack all the way. It does work with the other squared off forend they have😮‍💨

😀✌️👍‼️

Your tumbler has one problem. The rib on the side that contacts the rollers should be molded wider because many calibers of handgun brass like 45acp and several others get jammed inside that rib and they don't tumble along with the rest of the brass inside.

I have only Sonic cleaned since I have been reloading and not once has my rifle said it doesn't care how shiny the cases are.

can the shell holder be removed from the rail mount?

Good design but bag is self destructed prematurely

Where can you get the cams and springs?

Have the trigger pull gauge, love it.